Double bike kickstand 24-28 inch for stable parking

Park a compatible bicycle with greater stability using this adjustable two-leg kickstand. Both legs fold down beneath the frame to create a wider support base than a single bike kickstand. This helps when loading panniers or parking a cargo bike. The stand fits 24, 26 or 28 inch wheels and mounts centrally beneath the frame.

The listed product dimensions are 3 x 28 x 33 cm. Its leg length can be adjusted to suit the wheel size and frame height. The product weighs 512 g and has a black finish. The product description identifies aluminium and iron, while the separate material specification lists iron. For accuracy, this product is not described here as an entirely aluminium or fully rustproof stand.

Main features

• Suitable for bicycles with 24, 26 or 28 inch wheels
• Adjustable twin-leg design for a balanced parking position
• Central installation beneath the frame near the bottom bracket
• Supplied with an M9 x 30 mm mounting bolt
• Iron mounting plate measuring 6 x 3 cm
• Listed product dimensions: 3 cm long, 28 cm wide and 33 cm high
• Product weight: 512 g
• Colour: black
• Package dimensions: 26 x 21 x 20 cm
• No manufacturer’s warranty specified

Which bicycles can use this stand?

This double bike stand is intended for bicycles equipped with a central kickstand mount behind the bottom bracket. Many city, cargo, utility and trekking bikes use this fitting. Some electric bikes do as well. The maximum load capacity has not been specified, so nobody should sit on the bicycle while it rests on the stand.

The stand may also suit a hybrid bike when its frame has a flat mounting surface or kickstand plate with a compatible bolt hole. Before fitting, confirm that brake and gear cables remain unobstructed, the crank arms cannot strike the folded legs and the rear tyre has enough clearance.

Compatibility with a mountain bike requires additional checks. Many mountain bikes do not have a central kickstand plate, and wide tyres, cable routing or rear suspension components may occupy the installation area. Do not clamp this stand around a carbon frame or a thin frame tube unless the bicycle manufacturer expressly permits that installation method.

Road frames also commonly lack the required mounting point and are not designed for a kickstand clamped around their tubes. Check the manufacturer’s instructions before buying a road bike stand. Without an approved central mount, use a separate floor stand instead.

How to install the double bicycle stand

1. Support the bicycle upright. Remove the existing centre stand, if present, and clean the mounting surface.
2. Locate the kickstand plate behind the bottom bracket. Check that its hole accepts the supplied M9 x 30 mm bolt. Do not use the bolt if its diameter, thread or usable length is incorrect.
3. Position the double kickstand squarely beneath the frame. Fit the 6 x 3 cm iron plate as required by the frame construction, making sure no cable, hose or wire becomes trapped.
4. Start the bolt by hand to avoid cross-threading. Tighten it to the torque specified by the bicycle or frame manufacturer. No torque is provided for this kickstand, so do not estimate one.
5. Adjust both legs to the same effective length. In the parking position, the bicycle should sit securely without leaning sharply forwards, backwards or towards either side.
6. Fold the stand in and out several times. Check the clearance around the crank, chain, cables, rear tyre and pedals. Inspect the bolt and stand again after the first ride.

Practical use and maintenance

Use the stand on firm, level ground. Hold the handlebar and lower the kickstand while guiding the bike slightly backwards. Balance luggage between both sides before releasing the bicycle. This kickstand is not a repair stand and must not support a seated person.

Remove sand, road salt and dirt with a dry or damp cloth. Check the bolt and both leg settings regularly. Stop using the stand if you notice play, bending, cracks or substantial corrosion.

Compared with a single bicycle kickstand, this reinforced double stand places two contact points on the ground. A rear-chainstay kickstand may be more appropriate when the bicycle has no central mounting plate. Measure and inspect more than the wheel diameter before ordering: check the mounting interface, bolt compatibility and available space beneath the frame.

For shoppers seeking an affordable bike kickstand, this model provides an adjustable 24-28 inch solution with a mounting bolt. If you plan to buy a double bike kickstand, verify the central mount first. Discountershop also offers other bicycle accessories and bicycle parts for everyday riding and maintenance.

Buy from Discountershop

Package contents

• One black double bicycle kickstand for 24-28 inch bikes
• One M9 x 30 mm mounting bolt
• One 6 x 3 cm iron mounting plate
• Manual: listed as universal

Frequently asked questions

Does this double bike kickstand fit every 24 to 28 inch bicycle?

No. Wheel size alone does not determine compatibility. The bicycle needs an approved central mounting point, a suitable M9 thread and sufficient clearance around the crank, tyre and cables. Always check the frame manufacturer’s instructions.

Can I install this kickstand on a mountain bike or road bike?

Only if the frame has a compatible centre mount. Many mountain and road bikes lack this fitting or have cables, suspension parts or wide tyres nearby. Never clamp the stand to carbon tubes without manufacturer approval.

How do I adjust this kickstand for a 28 inch bicycle?

Mount the stand centrally and set both legs to equal lengths. Test it on level ground: the bicycle should remain balanced, while the crank arms, pedals, cables and rear tyre must clear the folded mechanism.

Is this the best double kickstand for a loaded cargo bike?

That depends on frame compatibility and total load. The two legs create a broad base, but no maximum capacity is specified. Check the mounting bolt regularly and never leave anyone sitting on the parked bicycle.